High performance additive that quiets noise from contaminated and sticky hydraulic valve lifters. Improves lubrication properties of the oil and cleans valve bores. ...
Part No: 20004
Meets DOT 4 specifications. Dry Boiling Point: 265 deg. C (509 deg. F). Wet Boiling Point: 155 deg. C (311 deg. F). ...
Part No: 12614
Silicone-based, permanently elastic sealing compound. Temperature resistant up-to more than 200 deg. C. For all surface and flange seals on engines and transmissions. Color: transparent. ...
Part No: 559526014
Raises oil viscosity and regenerates rubber & plastic engine seals to reduce oil consumption. ...
Part No: 2020
Hypoid gear oil with limited slip additive. Meets Specifications: API GL-5. ...
Part No: 21727
Exceeds DOT 4 specifications. Dry Boiling Point: 280 deg. C (536 deg. F). Wet Boiling Point: 198 deg. C (388 deg. F). ...
Meets Specifications: API GL-5, MIL-L-2105C/D. ...
Part No: 600891626
Forms a high load-bearing film of lubricant on all friction surfaces. ...
Part No: 2019
Used in the cleaning and flushing process of diesel particulate filters. Powder coated aluminum container with standard compressed air connection and check valve. 1-liter capacity. Used in conjunction with part # 20110 DPF Cleaning Fluid, part # 20112 DPF Cleaning Flush and part # 7945 DPF Cleaning Wand Kit. ...
Part No: 7946
Exceeds DOT 4 specifications. Dry Boiling Point: 280 deg. C (536 deg. F). Wet Boiling Point: 198 deg. C (388 deg. F). ...
Meets DOT 4 specifications. Dry Boiling Point: 260 deg. C (500 deg. F). Wet Boiling Point: 165 deg. C (329 deg. ...
Brake Light Switch on Master Cylinder (2 Pole Connection) 113945515H Porsche 911 Carrera 1984 ...
Grommet - Brake Master Cylinder to Reservoir 91135592200 Porsche 911 S 1977 ...
Grommet - Brake Master Cylinder to Reservoir/Lines 90135592900 Porsche 356C Base 1964 ...
Converts rust into a black inert dust. Apply product via brush or sprayer. Allow product around 24 hours to work. Rinse the black dust off. What is left behind is the metal protected by a black zinc phosphate coating. This coating is good for up to six months protection and can be painted directly over. ...
Part No: 22820
Meets Specifications: ACEA A1/B1, BMW Longlife 14 FE+, Jaguar/Land Rover STJLR.51.5122. ...
Meets Specifications: API SM/CF, BMW Longlife 98, M/B 229.3, Audi/VW 502.00 & 505.00, Porsche A40. ...
Part No: 2049
Meets Specifications: API SM/CF, BMW Longlife 98, M/B 229.3, Audi/VW 502.00 & 505.00, Porsche A40. ...
Part No: 2050
Meets Specifications: API SN/CF, BMW Longlife 04, M/B 229.31, 229.51, & 229.52, Audi/VW 502.00 & 505.00. ...
Part No: 2244
Cleans thoroughly and prevents deposits from forming in fuel systems and combustion chambers. Keeps the injectors clean and improves engine combustion leading to lower fuel consumption and maximum engine performance. For use with all diesel engines both with and without diesel particulate filters. Perfectly compatible with all conventional and biodiesel fuels. For best results add to fuel system ...
Part No: 2002
Pre-moistened with a powerful cleaning formula that is capable of removing tar, grease, wax, ink, paint, lubricants and adhesives. They leave behind a fresh citrus scent as they clean. While effective on tough grime, the cleaning formula is enhanced with natural oils and emollients. The abrasive yet non-stratching fabric aids in cleaning and replaces the need for messy, ineffective rags and soap. ...
Part No: 34943
Cleans and flushes out the engine oil system. Add to a warm engine, idle for 10 minutes, then drain. ...
Part No: 2037
Meets Specifications: API GL-5. ...
Part No: 21687
Brake Assembly Lubricant - Ate Plastilube (75 ml. Tube) 700015 Porsche 356B Base 1963 ...
Detects position of the ABS sensor ring in wheel bearings for correct installation. ...
Meets DOT 4 specifications. Dry Boiling Point: 265 deg. C (509 deg. F). Wet Boiling Point: 155 deg. C (311 deg. F). ...
Part No: 12509
Meets Specifications: API SL/CF. ...
Part No: 2043
Engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. More thermally stable in comparison to other leading brands; resists breaking down due to heat for a longer period of time. Lower moisture content than other oils due to special packaging and handling procedures. ...
Part No: 13119